檢測項目（部分）
螺栓連接副施工扭矩
緊固件楔負載
螺栓連接副預拉力
無縫鋼管內部缺陷（超聲波檢測）
螺栓硬度
涂層附著力
幾何尺寸
焊縫內部質量（射線檢測）
高強度扭剪型螺栓緊固軸力
高強度大六角頭螺栓 連接副扭矩系數
螺母硬度
防護涂裝層厚度
鋼結構焊縫缺陷
普通螺栓最小拉力載荷
緊固件實物拉力
焊縫內部質量（超聲檢測）
高強度大六角頭螺栓連接副扭矩系數
高強度螺栓連接摩擦面的抗滑移系數
緊固件脫碳試驗
原材料檢測
焊縫尺寸
焊縫內部質量(超聲檢測)
檢測樣品（部分）
鋼構件
檢測標準（部分）
國家標準 GB/T 18226-2015 公路交通工程鋼構件防腐技術條件
【適用范圍】本標準規定了公路交通工程鋼構件防腐術語與定義、分類、使用原則、技術要求和試驗方法。rn本標準適用于公路交通工程各種鋼構件的防腐。其他道路交通工程鋼構件的防腐可參照執行。
【中國標準分類】 A29 基礎標準
【國際標準分類】 25.220-表面處理和涂覆
國家標準 GB/T 18226-2000 高速公路交通工程鋼構件防腐技術條件
【適用范圍】 本標準規定了高速公路交通工程鋼構件的防腐形式及防腐要求。rn 本標準適用于高速公路交通工程各種鋼構件的防腐。其他公路交通工程鋼構件的防腐可參照執行。
【中國標準分類】 R18 公路運輸
【國際標準分類】 93.080.01-道路工程綜合
國家標準 GB/T 30064-2013 金屬材料 鋼構件斷裂檢測中裂紋尖端張開位移(CTOD)斷裂韌度的拘束損失修正方法
【適用范圍】在含裂紋鋼結構的斷裂檢測中
一般假設斷裂韌度試樣的杭斷能力與構件抗斷能力是相等的
但這種假設往往導致過于保守的斷裂檢測結果。這是由于構件在主要受拉伸荷載作用時
裂紋尖端附近區域出現塑性拘束損失所致
相比之下斷裂韌度試樣由于承受彎曲荷載作用條件而在裂紋尖端附近區域產生很高的多軸拘束應力狀態。最近幾年來廣泛應用于工程結構中的高強度鋼因其屈強比較高(屈服強度/抗拉強度)而表現出構件裂紋尖端的拘束損失十分顯著
斷裂檢測中迫切地需要進行修正。本標準規定了一種方法
通過考慮拘束損失
將通過試驗試樣得到的CTOD(裂紋尖端張開位移)斷裂韌度轉化為構件等效CTOD。這種方法適用于使用應力強度因子和J積分概念所進行的斷裂韌度檢測。本標準適用于由裂紋類缺陷或鐵素體結構鋼疲勞裂紋所引發的失穩斷裂
失穩斷裂前出現明顯的延性裂紋擴展情況不包括在本標準的適用范圍之內。結構鋼CTOD斷裂韌度按照ISO 12135-2002
BS 7448-1-1991或ASTM E1290-1999中任何一個規范中所規定的相應程序進行測試。含裂紋構件的斷裂檢測通常使用一種相關機構認可的方法進行
如FAD(失效評定圖)
相關細節本標準沒有提及。本標準可用于消除過度保守觀念
這種保守觀念與傳統斷裂力學方法有著密切聯系。既可以通過結構鋼斷裂韌度精確地檢測構件失穩斷裂的初始界限，也可用于合理地確定材料斷裂韌度臨界值（驗收值），以滿足有關鋼構件對材料成型性能方面的設計要求。
【中國標準分類】 H22 金屬理化性能實驗方法
【國際標準分類】 77.040.10-金屬材料力學試驗
國家標準 GB/T 41951-2022 輸變電工程鋼構件熱浸鍍鋅鋁鎂稀土合金鍍層技術條件
【適用范圍】本文件規定了輸變電工程鋼構件熱浸鍍鋅鋁鎂稀土合金鍍層的一般規定、技術要求、試驗方法、檢驗規則、標記。
本文件適用于輸變電工程鋼制桿塔、變電站構支架及其緊固件等鋼構件熱浸鍍鋅鋁鎂稀土合金鍍層。
本文件適用于輸變電工程鋼制桿塔、變電站構支架及其緊固件等鋼構件熱浸鍍鋅鋁鎂稀土合金鍍層。
【中國標準分類】 K47 輸變電設備
【國際標準分類】 25.220.40-金屬鍍層
行業標準 JG/T 144-2016 門式剛架輕型房屋鋼構件
【適用范圍】本標準規定了門式剛架輕型房屋鋼構件的術語和定義、代號和型號、一般規定、要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存等。rn本標準適用于一般工業與民用建筑的門式剛架輕型房屋鋼結構構件。
【中國標準分類】 P26 工程結構
【國際標準分類】 91.080.10-金屬結構
行業標準 JG/T 144-2002 門式剛架輕型房屋鋼構件
【適用范圍】本標準規定了門式剛架輕型房屋鋼構件的代號、要求、試驗方法、檢驗規則、標志、包裝、運輸和儲存等。rnt本標準適用于一般工業與民用建筑的門式剛架輕型房屋鋼結構構件，類似鋼構件可參照使用。本標準未規定的，應按國家現行有關標準規定執行。
【中國標準分類】 Q73 建筑構配件與設備
【國際標準分類】 91.060.99-建筑物的其他構件
行業標準 JT/T 657-2006 交通鋼構件聚苯胺防腐涂料
【適用范圍】 本標準規定了聚苯胺防腐涂料的產品分類、技術要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存等內容。rn 本標準適用于公路交通鋼構件用聚苯胺防腐涂料。其他鋼構件用聚苯胺防腐涂料可參照使用。
【中國標準分類】 P66 交通運輸工程
【國際標準分類】 25.220.40-金屬鍍層
行業標準 JT/T 684-2007 鋼構件鍍鋅層附著性能測定儀
【適用范圍】本標準規定了鋼構件鍍鋅層附著性能測定儀的技術要求、試驗方法、檢驗規則以及標志、包裝、運輸與儲存等。n本標準適用于公路用鋼構件鍍鋅層附著性能測定儀的生產、檢驗和使用。
【中國標準分類】 Y82 交通運輸工程
【國際標準分類】 97.140-家具
行業標準 CB 1200.1-1988 玻璃鋼構件的強度計算夾層板
【適用范圍】本標準規定了玻璃鋼夾層板的設計計算方法。rn 本標準適用于面層為雙向正交異性或各向同性，芯材為輕木、泡沫塑料(主要是硬質泡沫塑料)和泡沫塑料與玻璃鋼腹板組合結構的玻璃鋼夾層板的設計計算。
【中國標準分類】 V11 材料與工藝
【國際標準分類】 47.020.10-船體及其構件
行業標準 JJG (交通) 082-2007 鋼構件鍍鋅層附著性能測定儀檢定規程
【適用范圍】本規程適用于公路用鋼構件鍍鋅層附著性能測定儀的首次檢定、后續檢定和使用中檢驗。
【中國標準分類】 A53 計量
【國際標準分類】 17.100-力、重力和壓力的測量
行業標準 YB/T 4663-2018 異形鋼構件
【適用范圍】本標準規定了異形鋼構件的術語和定義、符號和說明、分類和代號、訂貨內容、外形尺寸和允許偏差、技術要求、試驗方法、檢驗規則、包裝、標志和質量證明書、運輸和貯存。
本標準適用于建筑鋼結構用異形鋼構件，其他領域用異形鋼構件、異形鑄鋼節點和不銹鋼構件可參照使用。
本標準適用于建筑鋼結構用異形鋼構件，其他領域用異形鋼構件、異形鑄鋼節點和不銹鋼構件可參照使用。
【中國標準分類】 H44 鋼鐵產品
【國際標準分類】 77.140.60-鋼棒和鋼條
國際標準 ISO 834-10-2014 防火試驗--建筑物構件--第10部分: 結構鋼構件用防火材料的貢獻率測定的具體要求
【適用范圍】This part of ISO 834 specifies a method for testing fire protection systems applied to structural steel members used in buildings as beams
columns
or tension members. This part of ISO 834 is intended for use in conjunction with the assessment protocol described in ISO 834-11. It applies to steel sections (including hollow sections) and only considers sections without openings in the web. Results from analysis of I or H sections are directly applicable to angles
channels
and T-sections for the same section factor
whether used as individual members
e.g. bracing
or part of a fabricated structural system such as a steel truss construction. This part of ISO 834 does not apply to solid bar
rod
or concrete-filled hollow sections. This part of ISO 834 describes the fire test procedures that specify the tests which should be carried out to determine the ability of the fire protection system to remain sufficiently coherent and in position for a well-defined range of deformations
furnace
and steel temperatures
such that the efficacy of the fire protection system is not significantly impaired
and to provide data on the thermal characteristics of the fire protection system when exposed to the standard temperature/time curve specified in ISO 834-1. In special circumstances
where specified in National Building Regulations
there can be a requirement to subject reactive fire protection materials to a smouldering curve. The test and the requirements for its use are described in Annex G. This part of ISO 834 is applicable to both passive and reactive fire protection systems as defined in the terms and definitions
which are installed or applied in such a way that they remain in place for the intended duration of fire exposure. The fire test methodology makes provision for the collection and presentation of data which is then used as direct input into ISO 834-11 to determine the limits of direct application to steel sections of various shapes
sizes
and fire resistance periods
【中國標準分類】 N64 實驗室儀器與真空儀器
【國際標準分類】 71.040.20-實驗室器皿和有關儀器
國際標準 ISO 834-11-2014 防火試驗--建筑物構件--第11部分: 結構鋼構件用防火材料檢測的特定要求
【適用范圍】The assessment detailed in this part of ISO 834 is designed to cover a range of thicknesses of the firenprotection material
a range of steel sections characterized by their section factors
a range of designntemperatures
and a range of valid fire resistance classification periods.nThis part of ISO 834 covers fire protection systems that include both passive (boards
mats
slabs
andnspray materials) and reactive materials as defined in this document.nThe assessment procedure is used to establishna) on the basis of the temperature data derived from testing loaded and unloaded specimens
ancorrection factor and practical constraints on the use of the fire protection system (the physicalnperformance) andnb) on the basis of the temperature data derived from testing unloaded short steel specimens
thenthermal properties of the fire protection material (the thermal performance).nThe limits of applicability of the results of the assessment are defined together with permitted directnapplication of the results to different steel section sizes and strength grades (but not stainless steels)nand to the fire protection system tested. The results of the tests obtained according to ISO 834-10 andnthe assessment in this part of ISO 834 are directly applicable to steel sections of “I” and “H” crosssectionalnshape and hollow sections. Results from analysis of I or H sections are directly applicable tonangles
whether used as individual elements or asnpart of a fabricated steel truss.nThe results of the assessment are applicable to fabricated sections.nThis part of ISO 834 does not apply to concrete-filled hollow sections
beams
or columns containingnholes or openings of any type or solid bar.nAny assessment method is acceptable provided it meets the acceptability criteria given in 5.5. Examplesnof assessment methods in common use are given in Annexes C to G.
【中國標準分類】 N64 實驗室儀器與真空儀器
【國際標準分類】 71.040.20-實驗室器皿和有關儀器
國際標準 ISO 12944-1-1998 色漆和清漆--使用防護漆對鋼構件作防腐蝕處理--第1部分：概述。
【適用范圍】1 ISO 12944 deals with the corrosion protection of steel structures by protective paint systems.n2 ISO 12944 covers only the corrosion-protective function of paint systems. Other protective functions
like the protection against:n— microorganisms (marine fouling
bacteria
fungi
etc.)
n— chemicals (acids
alkalis
organic solvents
gases
n— mechanical action (abrasion
etc.) andn— firenare not covered by ISO 12944.n3 The field of application is characterized by:n— the type of structure
n— the type of surface and surface preparation
n— the type of environment
n— the type of protective paint system
n— the type of work andn— the durability of the protective paint system.nAlthough ISO 12944 does not cover all types of structure
surface and surface preparation
it may
by agreement
also be applied to those cases which are not covered by the standard.nThe various aspects of the field of application are described in more detail in 1.3.1 to 1.3.6.n3.1 Type of structurenISO 12944 concerns structures made of carbon or low-alloy steel (e.g. in accordance with EN 10025) of not less than 3 mm thickness
which are designed using an approved strength calculation.nNot covered by ISO 12944 are concrete structures reinforced with steel.n3.2 Type of surface and surface preparationnISO 12944 deals with the following types of surface consisting of carbon or low-alloy steel
and their preparation:n— uncoated surfaces;n— surfaces thermally sprayed with zinc
aluminium or their alloys;n— hot-dip-galvanized surfaces;n— zinc-electroplated surfaces;n— sherardized surfaces;n— surfaces painted with prefabrication primer;n— other painted surfaces.n3.3 Type of environmentnISO 12944 deals with:n— six corrosivity categories for atmospheric environments
n— three categories for structures immersed in water or buried in soil.n3.4 Type of protective paint systemnISO 12944 covers a range of paint products which dry or cure at ambient conditions. Not covered by ISO 12944 are:n— powder coating materials
n— stoving enamels
n— heat-cured paints
n— coatings of more than 2 mm dry-film thickness
n— linings of tanks
n— products for the chemical treatment of surfaces (e.g. phosphating solutions).n3.5 Type of worknISO 12944 covers both new work and maintenance.n3.6 Durability of the protective paint systemnISO 12944 considers three different durability ranges (low
medium and high). See 3.5 and clause 4.nThe durability range is not a "guarantee time".
【中國標準分類】 A29 涂料、顏料、染料
【國際標準分類】 87.020-涂覆工藝
國際標準 ISO 12944-6-1998 色漆和清漆--使用防護漆對鋼構件作防腐蝕處理--第6部分：實驗室性能試驗方法。
【適用范圍】This part of ISO 12944 specifies laboratory test methods and test conditions for the assessment of paint systems for the corrosion protection of steel structures. The test results are to be considered as an aid in the selection of suitable paint systems and not as exact information for determining durability.nThis part of ISO 12944 covers protective paint systems designed for application to uncoated steel
hot-dip-galvanized steel and steel surfaces with thermally sprayed zinc coatings.nThis part of ISO 12944 does not apply to protective paint systems for electroplated or painted steel.nCertain tests in this part of ISO 12944 are not applicable to many water-borne paint systems (see 4.2). Nevertheless
some water-borne paint systems are amenable to testing and evaluation using the procedures described herein
and their results could be taken into account.nThe environments defined in ISO 12944-2 are considered.
【中國標準分類】 G51 涂料、顏料、染料
【國際標準分類】 87.020-涂覆工藝
國際標準 ISO 12944-8-2017 色漆和清漆--使用防護漆對鋼構件作防腐蝕處理--第8部分：對新工藝及維護的規范的開發
【適用范圍】This document covers the development of specifications for corrosion protection of steel structures using protective paint systems. It relates to new work and maintenance in the workshop or on site and is also applicable to the corrosion protection of individual components. This document covers the corrosion protection of steel structures exposed to different corrosion stresses by environments such as indoors
open-air and immersion in water or burial in soil
as well as special stresses
due for example
to medium or high temperatures. The need for different durability ranges is considered.
Steel surfaces that have been hot-dip-galvanized metal-sprayed zinc-electroplated or sherardized and previously painted steel surfaces are also covered by this document.
In this document reference areas for assessing the quality of the corrosion protection work and the performance of the protective paint systems used are dealt with.
This document provides detailed flow charts for planning new work and maintenance which are taken into account when writing a specification. This document can also be used as a guide if extreme corrosion stresses or high temperatures occur or if the protective paint systems are to be used on other substrates such as non-ferrous metals or concrete to define suitable specifications.
Steel surfaces that have been hot-dip-galvanized metal-sprayed zinc-electroplated or sherardized and previously painted steel surfaces are also covered by this document.
In this document reference areas for assessing the quality of the corrosion protection work and the performance of the protective paint systems used are dealt with.
This document provides detailed flow charts for planning new work and maintenance which are taken into account when writing a specification. This document can also be used as a guide if extreme corrosion stresses or high temperatures occur or if the protective paint systems are to be used on other substrates such as non-ferrous metals or concrete to define suitable specifications.
【中國標準分類】 G51 涂料、顏料、染料
【國際標準分類】 87.020-涂覆工藝
國際標準 ISO 12944-4-2017 色漆和清漆---使用防護漆對鋼構件作防腐蝕處理--第4部分：表面類型和表面處理
【適用范圍】This document covers the following types of surfaces of steel structures consisting of carbon or low- alloy steel
and their preparation:
— uncoated surfaces;
— surfaces thermally sprayed with zinc aluminium or their alloys;
— hot-dip-galvanized surfaces;
— zinc-electroplated surfaces;
— sherardized surfaces;
— surfaces painted with prefabrication primer;
— other painted surfaces.
This document defines a number of surface preparation grades but does not specify any requirements for the condition of the substrate prior to surface preparation.
Highly polished surfaces and work-hardened surfaces are not covered by this document.
— uncoated surfaces;
— surfaces thermally sprayed with zinc aluminium or their alloys;
— hot-dip-galvanized surfaces;
— zinc-electroplated surfaces;
— sherardized surfaces;
— surfaces painted with prefabrication primer;
— other painted surfaces.
This document defines a number of surface preparation grades but does not specify any requirements for the condition of the substrate prior to surface preparation.
Highly polished surfaces and work-hardened surfaces are not covered by this document.
【中國標準分類】 A29 基礎標準
【國際標準分類】 25.220.10-表面預處理
國際標準 ISO 12944-2-2017 色漆和清漆---使用防護漆對鋼構件作防腐蝕處理--第2部分：環境分類。
【適用范圍】This document deals with the classification of the principal environments to which steel structures are exposed
and the corrosivity of these environments. This document
— defines atmospheric-corrosivity categories based on mass loss (or thickness loss) by standard specimens and describes typical natural atmospheric environments to which steel structures are exposed giving advice on the estimation of the corrosivity
— describes different categories of environment for structures immersed in water or buried in soil and
— gives information on some special corrosion stresses that can cause a significant increase in corrosion rate or place higher demands on the performance of the protective paint system.
The corrosion stresses associated with a particular environment or corrosivity category represent one essential parameter governing the selection of protective paint systems.
— defines atmospheric-corrosivity categories based on mass loss (or thickness loss) by standard specimens and describes typical natural atmospheric environments to which steel structures are exposed giving advice on the estimation of the corrosivity
— describes different categories of environment for structures immersed in water or buried in soil and
— gives information on some special corrosion stresses that can cause a significant increase in corrosion rate or place higher demands on the performance of the protective paint system.
The corrosion stresses associated with a particular environment or corrosivity category represent one essential parameter governing the selection of protective paint systems.
【中國標準分類】 G51 涂料、顏料、染料
【國際標準分類】 87.020-涂覆工藝
國際標準 ISO 12944-1-2017 色漆和清漆--使用防護漆對鋼構件作防腐蝕處理--第1部分：概述
【適用范圍】This document defines the overall scope of ISO 12944 (all parts). It gives some basic terms and definitions and a general introduction to the other parts of ISO 12944. Furthermore
it includes a general statement on health
safety and environmental protection
and guidelines for using ISO 12944 (all parts) for a given project.
【中國標準分類】 G51 涂料、顏料、染料
【國際標準分類】 87.020-涂覆工藝
國際標準 ISO 12944-3-2017 色漆和清漆---使用防護清對鋼構件作防腐蝕處理--第3部分：設計依據
【適用范圍】This document deals with the basic criteria for the design of steel structures to be coated by protective paint systems in order to avoid premature corrosion and degradation of the coating or the structure. It gives examples of appropriate and inappropriate design
indicating how problems of application
inspection and maintenance of paint systems can be avoided. Design measures which facilitate handling and transport of the steel structures are also considered.
【中國標準分類】 G51 涂料、顏料、染料
【國際標準分類】 87.020-涂覆工藝
國際標準 ISO 12944-7-2017 色漆和清漆--使用防護漆對鋼構件作防腐蝕處理--第7部分：油漆工作的施工和監督
【適用范圍】This document deals with the execution and supervision of paint work on steel structures in the workshop or on site. This document does not apply to
— the preparation of surfaces to be painted (see ISO 12944-4) and the supervision of such work
— the application of metallic coatings and
— pre-treatment methods such as phosphating and chromating and paint application methods such as dipping powder coating or coil coating.
— the preparation of surfaces to be painted (see ISO 12944-4) and the supervision of such work
— the application of metallic coatings and
— pre-treatment methods such as phosphating and chromating and paint application methods such as dipping powder coating or coil coating.
【中國標準分類】 G51 涂料、顏料、染料
【國際標準分類】 87.020-涂覆工藝
國外標準 ASTM C645-2004a 非結構鋼構件標準規范
【適用范圍】
1.1 This specification covers nonstructural steel framing members in interior construction assemblies.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are for information purposes only.
1.3 The following safety hazards caveat pertains only to the test method portion Sections 9 and 10 of this specification: This standard does not purport to address all of the safety concerns if any associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
【中國標準分類】 Q73 建筑構配件與設備
【國際標準分類】 91.060.10-墻、隔墻、房屋正面
國外標準 ASTM C645-2011a 非結構鋼構件標準規范
【適用范圍】
1.1 This specification covers nonstructural steel framing members in interior construction assemblies.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are for information purposes only.
1.3 The following safety hazards caveat pertains only to the test method portion
國外標準 ASTM C645-2004 非結構鋼構件標準規范
【適用范圍】
1.1 This specification covers nonstructural steel framing members in interior construction assemblies.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are for information purposes only.
1.3 The following safety hazards caveat pertains only to the test method portion
國外標準 BS EN 13381-8-2010 測定結構構件耐火作用的試驗方法.鋼構件應用的保護方法
【適用范圍】This European Standard specifies a test method for determining the contribution made by appliednreactive fire protection systems to the fire resistance of structural steel members
which can be usednas beams or columns. It considers only sections without openings in the web. It is not directlynapplicable to structural tension members without further evaluation. Results from analysis of I or Hsectionsnare directly applicable to angles
channels and T-sections for the same section factor
nwhether used as individual elements or as bracing. This European Standard does not apply to solidnbar or rod.nIt covers fire protection systems that involve only reactive materials and not to passive fire protectionnmaterials as defined in this document.nThe evaluation is designed to cover a range of thicknesses of the applied fire protection material
anrange of steel sections
characterized by their section factors
a range of design temperatures and anrange of valid fire protection classification periods.nThis European Standard contains the fire test procedures
which specifies the tests which should bencarried out to determine the ability of the fire protection system to remain coherent and attached to thensteelwork
and to provide data on the thermal characteristics of the fire protection system
whennexposed to the standard temperature/time curve specified in EN 1363-1.nIn special circumstances
there can be a need tonsubject reactive protection material to a smouldering curve
the test for this and the specialncircumstances for its use are described in Annex A.nThe fire test methodology makes provision for the collection and presentation of data
which can benused as direct input to the calculation of fire resistance of steel structural members in accordance withnthe procedures given in EN 1993-1-2 and EN 1994-1-2.nThis European Standard also contains the assessment
which prescribes how the analysis of the testndata shall be made and gives guidance on the procedures by which interpolation should benundertaken.nThe assessment procedure is used to establish:na) on the basis of temperature data derived from testing loaded and unloaded sections
a correctionnfactor and any practical constraints on the use of the fire protection system under fire testnconditions (the physical performance);nb) on the basis of the temperature data derived from testing short steel sections
the thermalnproperties of the fire protection system (the thermal performance).nThe limits of applicability of the results of the assessment arising from the fire test are defined
ntogether with permitted direct application of the results to different steel sections and grades and tonthe fire protection system.nThe results of the test and assessment obtained according to this European Standard are directlynapplicable to steel sections of I and H cross sectional shape and hollow sections.
【中國標準分類】 P26 工程結構
【國際標準分類】 13.220.50-建筑材料和構件的阻燃性
國外標準 BS ISO 27306-2009 金屬材料.鋼構件斷裂檢測CTOD斷裂韌性損失校正約束方法
【適用范圍】
【中國標準分類】 H22 金屬理化性能實驗方法
【國際標準分類】 77.040.10-金屬材料力學試驗
國外標準 DIN EN 13084-7 Berichtigung 1-2008 測定承重件耐火性能的試驗方法 第4部分：鋼構件的消防措施
【適用范圍】This part of ENV 13381 specifies a test method for determining the contribution made by applied fire protection systems to the fire resistance of structural steel members
which can be used as beams
columns or tension members. The evaluation is designed to cover a range of thicknesses of the applied fire protection material
a range of steel sections
a range of design temperatures and a range of valid fire protection classification periods.#
#
【中國標準分類】 C82 消防
【國際標準分類】 13.220.50-建筑材料和構件的阻燃性
國外標準 DIN EN 13381-8-2010 鋼構件涂覆層和鍍層防腐.第8部分:薄壁構件防腐
【適用范圍】
【中國標準分類】 A29 基礎標準
【國際標準分類】 25.220.10-表面預處理
國家標準 GB/T 18838.1-2002 涂覆涂料前鋼材表面處理 噴射清理用金屬磨料的技術要求 導則和分類
【適用范圍】GB／T l8838的本部分規定了涂覆涂料前鋼材表面噴射清理用的金屬磨料(以下簡稱金屬磨料)的分類和標記等。 本部分適用于未經使用過的金屬磨料的標記。 注1：雖然本部分IS0 11124是為滿足鋼構件處理要求而特別制定的，但規定的這些特性一般也適用于使用噴射清 理技術處理的其他材料的表面和部件。這些技術已在IS0 8504—2：2000((涂覆涂料前鋼材表面處理表面處理 方法第2部分：磨料噴射清理》中規定。
【中國標準分類】 A29 基礎標準
【國際標準分類】 25.220.10-表面預處理
國家標準 GB/T 18839.3-2002 涂覆涂料前鋼材表面處理 表面處理方法 手工和動力工具清理
【適用范圍】本標準規定了涂覆涂料前鋼材表面處理的方法一一手工和動力工具清理。 本標準適用于新的鋼構件，也適用于以前涂覆過涂料但有些區域受損或全部需要重新涂覆涂料的鋼材表面。
【中國標準分類】 A29 基礎標準
【國際標準分類】 25.220.10-表面預處理
檢測資質（部分）
檢測優勢
檢測實驗室（部分）
合作客戶（部分）
檢測報告作用
1、可以幫助生產商識別產品的潛在問題或缺陷，并及時改進生產工藝，保障產品的品質和安全性。
2、可以為生產商提供科學的數據，證明其產品符合國際、國家和地區相關標準和規定，從而增強產品的市場競爭力。
3、可以評估產品的質量和安全性，確保產品能夠達到預期效果，同時減少潛在的健康和安全風險。
4、可以幫助生產商構建品牌形象，提高品牌信譽度，并促進產品的銷售和市場推廣。
5、可以確定性能和特性以及元素，例如力學性能、化學性質、物理性能、熱學性能等，從而為產品設計、制造和使用提供參考。
6、可以評估產品是否含有有毒有害成分，以及是否符合環保要求，從而保障產品的安全性。
檢測流程
1、中析研究所接受客戶委托，為客戶提供檢測服務
2、客戶可選擇寄送樣品或由我們的工程師進行采樣，以確保樣品的準確性和可靠性。
3、我們的工程師會對樣品進行初步評估，并提供報價，以便客戶了解檢測成本。
4、雙方將就檢測項目進行詳細溝通，并簽署保密協議，以保證客戶信息的保密性。在此基礎上，我們將進行測試試驗.
5、在檢測過程中，我們將與客戶進行密切溝通，以便隨時調整測試方案，確保測試進度。
6、試驗測試通常在7-15個工作日內完成，具體時間根據樣品的類型和數量而定。
7、出具檢測樣品報告，以便客戶了解測試結果和檢測數據，為客戶提供有力的支持和幫助。
以上為鋼構件檢測的檢測內容，如需更多內容以及服務請聯系在線工程師。
