電氣性能檢測

電氣性能檢測簡介

發布時間：2025-05-03 21:31:06

更新時間：2025-09-25 09:29:04

咨詢點擊量：

第三方電氣性能檢測機構北京中科光析科學技術研究所科研分析中心作為綜合性研究所檢測中心，旗下實驗室擁有CMA檢測資質，檢測設備齊全，數據科學可靠，7-15個工作日便可出具電氣性能檢測報告。檢測樣品包含通訊電纜（電氣性能）、銅芯聚烯烴絕緣鋁塑綜合護套市內通信電纜(電氣性能)、綜合布線工程電氣測試/電纜系統電氣性能等。

咨詢檢測服務預約工程師

獲取檢測報價？

了解檢測儀器？

查看報告模板？

立即咨詢

電氣性能檢測內容

檢測信息（部分）

問題：電氣性能檢測主要針對哪些產品？

回答：電氣性能檢測涵蓋各類電子電氣設備及其組件，包括家用電器、工業設備、新能源產品、通信設備等，確保其符合安全、能效及電磁兼容性等標準。

問題：檢測的主要目的是什么？

回答：檢測旨在驗證產品的電氣安全、性能穩定性及合規性，降低使用風險，滿足市場準入要求，并為產品優化提供數據支持。

問題：檢測流程一般包括哪些步驟？

回答：流程通常分為樣品接收、預處理、參數測試、數據分析、報告生成五個階段，具體根據產品類型和標準要求調整。

檢測項目（部分）

絕緣電阻：評估材料絕緣性能，防止漏電風險。
耐壓強度：檢測介質在高電壓下的擊穿承受能力。
接地連續性：驗證設備接地路徑的可靠性。
泄漏電流：監測異常電流對用戶安全的潛在影響。
功率因數：衡量電能利用效率。
溫升測試：確認設備運行時溫度是否符合限值。
電磁兼容（EMC）：評估設備抗干擾及干擾他設備的能力。
諧波分析：檢測電流波形畸變對電網的影響。
輸入輸出特性：驗證設備額定參數與實際性能的一致性。
瞬態過電壓：模擬突發電壓沖擊下的設備穩定性。
介電損耗：反映絕緣材料能量損耗程度。
接觸電阻：測量導體連接處的導電效率。
工作頻率響應：分析設備在不同頻率下的性能變化。
短路保護：測試故障電流觸發保護裝置的靈敏度。
能效等級：評定產品能源消耗水平。
啟動特性：記錄設備通電初期的電流與電壓波動。
耐久性測試：模擬長期使用后的性能衰減情況。
靜電放電（ESD）：評估抗靜電干擾能力。
浪涌抗擾度：測試設備對瞬時高壓脈沖的耐受性。
電壓波動適應性：驗證供電不穩時設備的運行穩定性。

檢測范圍（部分）

家用電器
工業控制設備
新能源汽車部件
光伏逆變器
電池及充電設備
LED照明產品
信息技術設備
醫療電子儀器
低壓開關柜
電線電纜
電源適配器
電機與變壓器
電動工具
安防監控設備
通信基站設備
消費類電子產品
軌道交通電氣部件
智能家居設備
航空航天電子元件
可再生能源發電系統

檢測儀器（部分）

耐壓測試儀
絕緣電阻測試儀
示波器
頻譜分析儀
電參數測量儀
高低溫試驗箱
EMC測試系統
接地電阻測試儀
功率分析儀
諧波分析儀

檢測標準（部分）

國家標準 GB/T 14238-1993 電纜載波通信系統線路設備電氣性能

【適用范圍】

【中國標準分類】 K64 通信設備【國際標準分類】 29.120.40-開關

行業標準 JJG (船舶) 01-1990 印制電路用剛性基材電氣性能測試方法

【適用范圍】本標準規定了印制電路用剛性基材的電氣性能測試方法。
本標準適用于印制電路用剛性覆銅箔層壓板和粘結片。

【中國標準分類】 L30 電子元件【國際標準分類】 31.180-印制電路和印制電路板

行業標準 SJ 21183-2016 印制電路用撓性基材電氣性能測試方法

【適用范圍】本標準規定了印制電路用撓性基材電氣性能的測試方法。
本標準適用于印制電路用撓性覆銅箔層壓板、覆蓋層和粘結材料。

【中國標準分類】 L04 電子元器件與信息技術綜合【國際標準分類】 31.020-電子元件綜合

行業標準 YD/T 837.2-1996 通信光纜電氣性能試驗方法第1部分：金屬元構件的電氣連續性

【適用范圍】本部分規定了通信光纜中金屬元構件電氣連續性試驗的目的、試樣、設備、程序、要求和待規定細節等。本部分適用于通信光纜中加強構件、導電線、擋潮層、屏蔽層、護套和鎧裝層等金屬元構件的電氣連續性的試驗。

【中國標準分類】 M33 通信設備【國際標準分類】 33.180.10-光纖和光纜

地方標準 DB41/T 1685-2018 LED路燈、隧道燈用驅動電源電氣性能要求

【適用范圍】廣東省地方標準；------本標準適用于線路總功率不大于400 W的LED路燈、隧道燈用恒壓和恒流驅動電源

【中國標準分類】 T10 電源【國際標準分類】 43.060.50-電氣設備、控制系統

國際標準 ISO 22636-2020 粘合劑--地板覆蓋物用粘合劑--機械和電氣性能要求

【適用范圍】This document specifies characteristics for adhesives for floor coverings which comprise:
— resilient floor coverings (such as those manufactured from plastics linoleum or rubber);
— textile floor coverings.
Adhesives for floor coverings are intended for use within a building according to the manufacturer’s specification.
This document specifies requirements for establishing performance characteristics of adhesives for
floor coverings with regard to their determination evaluation and expression.
This document comprises all kinds of adhesives for floor coverings irrespective of the chemical
composition and the mechanism of setting. Products according to this document can be put on the
market as liquids pastes and film adhesives for floor coverings. The products can be one-component or multi-component.
This document also defines a special kind of adhesives for floor coverings which facilitate the easy
removal of the floor covering after the utilization and where the need for a permanent bond is not
always required. These types of floor covering adhesives are referred to as low peel strength release
bond adhesives.
This document does not:
— cover adhesives for bonding parquet to the subfloor adhesives for bonding laminate floor coverings and adhesives for ceramic tiles;
— make provisions for testing the bond strength of low peel strength release bond adhesives for floor coverings;
— take account of all influences which may occur in practice.

【中國標準分類】 G39 合成材料【國際標準分類】 83.180-粘合劑和膠粘產品

國際標準 IEC 60851-5-2008 繞組線--試驗方法--第5部分：電氣性能

【適用范圍】This part of IEC 60851 specifies the following tests:n- Test 5: Electrical resistance;n- Test 13: Breakdown voltage;n- Test 14: Continuity of insulation;n- Test 19: Dielectric dissipation factor;n- Test 23: Pin hole.nFor definitions general notes on methods of test and the complete series of methods of testnfor winding wires see IEC 60851-1.

【中國標準分類】 K12 電工材料和通用零件【國際標準分類】 29.060.10-電線

國際標準 IEC 62908-12-10-2017 觸摸和交互顯示器--第12-10部分:觸摸顯示器的測量方法--觸摸和電氣性能

【適用范圍】This part of IEC 62908 specifies the standard measuring conditions and methods for determining touch performance of a touch sensor module. This document is applicable to touch sensor modules where the structural relationship between touch sensor touch controller touch sensor module display panel touch display panel and touch display module is defined in IEC 62908-1-2.

【中國標準分類】 L38 電真空器件【國際標準分類】 31.120-電子顯示器件

國外標準 ASTM E1036-2008 用基準電池測定非聚光型地面光電模塊和數組電氣性能的試驗方法

【適用范圍】

It is the intent of these procedures to provide recognized methods for testing and reporting the electrical performance of photovoltaic modules and arrays.

The test results may be used for comparison of different modules or arrays among a group of similar items that might be encountered in testing a group of modules or arrays from a single source. They also may be used to compare diverse designs such as products from different manufacturers. Repeated measurements of the same module or array may be used for the study of changes in device performance.

Measurements may be made over a range of test conditions. The measurement data are numerically translated from the test conditions to standard RC to nominal operating conditions or to optional user-specified reporting conditions. Recommended RC are defined in Table 1.

If the test conditions are such that the device temperature is within x00B1;2x00B0;C of the RC temperature and the total irradiance is within x00B1;5 % of the RC irradiance the numerical translation consists of a correction to the measured device current based on the total irradiance during the I-V measurement.

If the provision in 5.3.1 is not met performance at RC is obtained from four separate I-V measurements at temperature and irradiance conditions that bracket the desired RC using a bilinear interpolation method.

There are a variety of methods that may be used to bracket the temperature and irradiance. One method involves cooling the module under test below the reference temperature and making repeated measurements of the I-V characteristics as the module warms up. The irradiance of pulsed light sources may be adjusted by using neutral density mesh filters of varying transmittance. If the distance between the simulator and the test plane can be varied then this adjustment can be used to change the irradiance. In natural sunlight the irradiance will change with the time of day or if the solar incidence angle is adjusted.

These test methods are based on two requirements.

First the reference cell (or module see 1.1.1 and 4.3.4) is selected so that its spectral response is considered to be close to the module or array to be tested.

Second the spectral response of a representative cell and the spectral distribution of the irradiance source must be known. The calibration constant of the reference cell is then corrected to account for the difference between the actual and the reference spectral irradiance distributions using the spectral mismatch parameter which is defined in Test Method E 973.

Terrestrial reference cells are calibrated with respect to a reference spectral irradiance distribution for example Tables G 173.

A reference cell made and calibrated as described in 4.3 will indicate the total irradiance incident on a module or array whose spectral response is close to that of the reference cell.

With the performance data determined in accordance with these test methods it becomes possible to predict module or array performance from measurements under any test light source in terms of any reference spectral irradiance distribution.

The reference conditions of 5.3.1 must be met if the measured I-V curve exhibits x201C;kinksx201D; or multiple inflection points.

TABLE 1 Reporting Conditions

Total Irradiance Wm^............

^{【中國標準分類】 F12 能源【國際標準分類】 27.160-太陽能工程}

^{國外標準 ASTM E1036-2002 使用標準電池的非聚能地面光電模件和陣列電氣性能的標準試驗方法}

^{【適用范圍】}

^{1.1 These test methods cover the electrical performance of photovoltaic modules and arrays under natural or simulated sunlight using a calibrated reference cell.}

^{1.2 Measurements under a variety of conditions are allowed; results are reported under a select set of reporting conditions (RC) to facilitate comparison of results.}

^{1.3 These test methods apply only to nonconcentrator terrestrial modules and arrays.}

^{1.4 The performance parameters determined by these test methods apply only at the time of the test and imply no past or future performance level.}

^{1.5 There is no similar or equivalent ISO standard.}

^{1.6 This standard does not purport to address all of the safety concerns if any associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.}

^{【中國標準分類】 F12 能源【國際標準分類】 27.160-太陽能工程}

^{國外標準 ASTM E1036-2012 塑料試驗方法.第2部分 :電氣性能.方法241A聚氯乙烯混合物對聚乙烯損耗角正切向影響測定}

^{【適用范圍】Describes a procedure for assessing the tendency of plasticized polyvinyl chloride compound to migrate into polyethylene materials with which it is in contact causing an increase in the loss tangent of the polyethylene.}

^{【中國標準分類】 G31 合成材料【國際標準分類】 83.080.20-熱塑性塑料}

^{國外標準 BS 4331-2-1972 超聲波探傷設備性能評定方法.第2部分:電氣性能}

^{【適用范圍】}

^{【中國標準分類】 M74 試驗給予無損探傷儀器【國際標準分類】 33.120.40-天線}

^{國外標準 BS 7825-3.2-1997 橡膠和塑料試驗設備的校準.校準一覽表.電氣性能}

^{【適用范圍】Provides schedules and guidance for the calibration of equipment and materials for a range of methods of tests for evaluating the electrical properties of plastics and rubber materials.}

^{【中國標準分類】 G31 合成材料【國際標準分類】 83.200-橡膠和塑料工業設備}

^{國外標準 BS EN 14259-2003 地板覆蓋物用膠粘劑.機械性能和電氣性能的要求}

^{【適用范圍】This European Standard specifies performance requirements of an adhesive when tested to a standard method with a characteristic type of floor covering. The values defined in this standard are considered to indicate a general suitability for use of an adhesive with the corresponding group of floor coverings. This standard can also be used for the evaluation of a particular floor covering with the corresponding type of adhesive. This standard does not contain criteria or recommendations for the practical installation of floor coverings. The values given in this standard also do not guarantee the complete functionality of combinations of adhesives and floor coverings in practical application.}

^{【中國標準分類】 G38 合成材料【國際標準分類】 83.180-粘合劑和膠粘產品}

^{國外標準 BS EN 60851-5-2008 繞組線.試驗方法.電氣性能}

^{【適用范圍】This part of IEC 60851 specifies the following tests:n– Test 5: Electrical resistance;n– Test 13: Breakdown voltage;n– Test 14: Continuity of insulation;n– Test 19: Dielectric dissipation factor;n– Test 23: Pin hole.nFor definitions general notes on methods of test and the complete series of methods of testnfor winding wires see IEC 60851-1.}

^{【中國標準分類】 K12 電工材料和通用零件【國際標準分類】 29.060.10-電線}

^{國外標準 DIN ISO 10330-1996 攝影.相機和閃光燈裝置的同步器.點火線路和連接器.電氣性能和試驗方法}

^{【適用范圍】}

^{【中國標準分類】 A15 經濟、文化【國際標準分類】 37.040.10-攝影設備、投影儀}

^{國外標準 DIN EN 13087-8-2005 防護頭盔試驗方法第8部分：電氣性能}

^{【適用范圍】This European Standard describes methods of test for protective helmets. The purpose of these tests is to enable assessment of the performance of the helmet as specified in the appropriate helmet standard. This standard specifies the methods of test for electrical properties. Additional text from CENELEC excluding reference to EN 50365:2002. This standard cannot be used for establishing electrical requirements for live working or working in the vicinity of live parts or electrical installations.}

^{【中國標準分類】 C73 勞動安全技術【國際標準分類】 13.340.20-頭部防護設備}

^{國外標準 DIN 44402-1-1974 電子管電氣性能測試. 測試方法準則.}

^{【適用范圍】Measurements of the electrical properties of electronic tubes and valves precautions relating to methods of measurementZusammenhang mit IEC-Publikation 151-0 Ausgabe 1966 siehe Erl?uterungen.Diese Norm enth?lt allgemeine Richtlinien die die Zuverl?s}